Quick Guide & Initial Setup

Welcome to AMG-Sicherheitstechnik! By choosing the CarPro-Tec Fusion, you've made an excellent decision. Protect yourself and your vehicle reliably from thieves and enjoy the reassuring feeling of security and control over your property. 

The CarPro-Tec Fusion is a unique plug-and-play alarm solution that constantly and reliably monitors your vehicle by simply inserting and activating it. Each CarPro-Tec Fusion is made in Germany and undergoes continuous quality control.

[email protected]

Downloads:

Quick Guide (EN)

Guide rapide (FR)

Kurzanleitung (DE)

TABLE OF CONTENTS

• Important note
• Charging & positioning
• Switch on & configure
• Connect
• Sensors and accessories

Important note

Please note that all sensors and accessory components supplied with your CarPro-Tec are already programmed and fully configured. 

Charge & Position 

Your CarPro-Tec comes pre-charged. Before starting the setup, please fully charge your CarPro-Tec using the included USB-C charging cable. The red LED inside the charging port will turn off once it is fully charged.

TFirst things first:

To optimise your new CarPro-Tec with our integrated room volume sensor for your vehicle, it must first be positioned at its final installation location as a basic requirement. This should be an easily accessible, but also visually protected location near a  5V/12V power supply  in the living area of your motorhome or caravan. Suitable mounting locations for this would be, for example, under a seating area, on the inside of your wardrobe or in any drawer. We recommend using the magnetic pad supplied to avoid any screwing or drilling in your vehicle.

Important: Only start adjusting the room volume sensor as described in step 2 below when your CarPro-Tec is in your chosen installation location.

Placing the CarPro-Tec in the rear garage is not recommended as this area is typically separated from the living space, making it difficult to achieve optimal settings for your camper. If you intend to use the CarPro-Tec in a regular car, consider placing it under the passenger seat, in the trunk, glove compartment, or spare tire well.

Switch on & configure

Note: Please carry out the following configuration steps without the indoor siren connected so that you are not unnecessarily exposed to our extremely loud siren.

1. Turning on the CarPro-Tec and activating the 4G module.

   Use a pointed object, such as a pen 

   Switch on CarPro-Tec: Briefly press the  SYSTEM   button If the leftmost green LED within the status bar lights up, the process was successful. Switch on the 4G module: Briefly press the 4G   button If the rightmost green LED within the status bar lights up, the process was successful.

2. Now set the rotary control of the room volume sensor to approx. 3 o'clock position (ninth line).
   
   
3. Now close all doors and windows of your vehicle from the inside and go to the door/window that is furthest away from the installation location of your CarPro-Tec.
   
   
4. Arm the CarPro-Tec with the remote control by briefly pressing the right button (closed lock symbol). A short beep confirms arming.
   
   
5. Now open the door or window with a sudden opening movement, just as you would in a burglary attempt. Your CarPro-Tec should now trigger an alarm.

   End the triggered test alarm by pressing the left button (open lock symbol) on the remote control. Two short beeps confirm that the monitoring has been deactivated.

   
   
6. Now optimize the setting of the room volume sensor for your vehicle by slightly reducing the sensitivity by one notch using the rotary control (turning it to the left). Then, repeat steps 4 and 5.
   
   
7. Repeat this step until it is no longer possible to trigger an alarm, even after several repetitions of sudden opening movements.
   
   
8. Now turn the room volume sensor back a maximum of half a mark, ideally between the last possible alarm triggering and the current position. This ensures that the integrated room volume sensor of your CarPro-Tec is not set too sensitively and only reacts to intrusion situations, but that false alarms are reduced to a minimum in exceptional situations such as severe thunderstorms (high pressure drop) or storms.
   
   
9. Congratulations, the room volume sensor is now optimally adjusted to your vehicle! Now place the optionally ordered accessories such as our door/window contacts, gas sensors or motion detectors with the help of our accessory QuickGuide. This also gives you precise instructions for the initial commissioning and positioning of the respective accessories for each sensor from our range in just a few steps.
   
   
10. Finally, position the supplied indoor siren in a separate, also visually protected location, hidden in your vehicle. If necessary, use the extension cable supplied with the siren.
    
    
11. Optional: Place the supplied status arming LED in the window frame, for example, so that you can see it clearly from the outside.

Connect

This is how you set up your CarPro-Tec to send smartphone alerts in case of an alarm while you’re on the move:

For reliable use of the internal GPS tracker, it is important that the CarPro-Tec is located in your vehicle and that it is in the open air in order to have sufficiently good GPS reception. Please note that the initial GPS localization may take several minutes. 

Install the “CarPro-Tec Fusion” app from your app store on your smartphone or tablet. Enter the required login credentials correctly, which can be found on the back of your device and on the last page of your quick-guide manual.

Once you have successfully logged in, the app is connected to your new CarPro-Tec. As soon as the CarPro-Tec detects an attempted break-in, you will receive an alarm notification including an updated GPS position on your smartphone via the app. You can repeat this step on multiple smartphones to expand the user circle as desired. Additionally, you can later add and monitor more CarPro-Tec devices in your app. 

Additional Information:

Sensors and accessories

Please note that all  accessories and sensors in your initial CarPro-Tec delivery are already fully programmed and preconfigured by us and only need to be placed in the correct location in your camping vehicle. For more information on the installation location, use of accessories and programming of reordered accessories, you can find the illustrated accessories guide in our  “Help & Support” section at www.carprotec.eu/en  .

More information:

For further information on the CarPro-Tec Fusion 4G, please use the download area under “Help & Support” at www.carprotec.eu/en. There you will find our detailed operating instructions for CarPro-Tec Fusion 4 G as a PDF download.

Battery law notice